Chapter 2: Difference between revisions

From Class Wiki
Jump to navigation Jump to search
Line 50: Line 50:
<br>
<br>


==Amplifier Circuits==
=Amplifier Circuits=
==Buffer Amplifier==
[[Image:BufferAmplifier.PNG|thumb|300px|Buffer Amplifier ]]
*Used to transfer voltage but not current to the following circuit. This amplifier can be used to negate the loading effects. No current flows through the amplifier, thus there is no voltage drop through the input resistor (going to the buffer amplifier).

<br>
<br>
<br>
<br>
<br>
<br>
<br>

==Inverting Amplifier==
[[Image:InvertingAmplifier.png|thumb|300px|Inverting Amplifier]]
*Uses negative feedback to invert and amplify voltage. Using nodal analysis at the negative terminal, the gain is found to be <math>-\frac{R_2}{R_1}</math>

<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
==Summing Amplifier==
[[Image:Summing_Amplifier.PNG‎|thumb|300px|Summing Amplifier]]
*<math>V_o=-R_f \left( \frac{V_3}{R_3}+\frac{V_2}{R_2}+\frac{V_1}{R_1}\right)</math>
*If all resistances are equal, then the output voltage is the (negative) sum of the input voltages

<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
==Noninverting Amplifier==
[[Image:Noninverting_Amplifier.PNG‎|thumb|300px|Noninverting Amplifier]]
*<math>V_o=V_{in} \left(1+\frac{R_2}{R_1}\right)</math>

<br>
<br>
<br>
<br>
<br>
<br>
<br>
==Differential Amplifier==
[[Image:Differential_Amplifier_2.PNG‎|thumb|300px|Differential Amplifier ]]
*<math>V_o=V_2\frac{(R_1+R_f)R_g}{(R_2+R_g)R_1}-V_1\frac{R_f}{R_1}</math>
*If you let <math>R_1=R_2\,</math> and <math>R_g=R_f\,</math> then the equation simplifies to <math>V_o=\frac{R_f}{R_1}(V_2-V_1)</math>

Revision as of 13:10, 12 January 2010

Ideal Op Amp Characteristics

  • Infinite input impedance
  • Infinite open-loop gain for the differential signal
  • Zero gain for the common mode signal
    • You can easily change an differential amplifier into a common-mode amplifier by grounding one of the inputs
  • Zero output impedance
  • Infinite bandwidth
    • To allow for infinite gain regardless of the frequency? Instantaneous feedback?

Op Amp Nodal Analysis

  • No current flows into the + or - terminals
  • If negative feedback is present (and no positive feedback), then
  • Write nodal equations at and , but not at
    • There is a voltage source inside the op amp. Writing a nodal equation at a voltage source adds an extra equation and an extra variable. You gain no ground.

DC imperfections

DC Imperfections
  • Bias currents, and , are the average dc currents flowing into the op amp input terminals. They can be caused by the signal source, feedback resistors, etc.
    • The bias current is the average of the dc currents.
  • Offset current is the difference between the bias currents.
  • Offset voltage occurs when the output voltage is nonzero for zero input voltage.

Canceling bias currents

  • Because bias currents flow have equal magnitude and direction, it is possible to negate their effects.
    • The orientation of the offset voltage and the direction of the offset current are unknown, thus it is not possible to correct for these parameters with a circuit design.

Steps

  1. Ground the input
  2. Set the output to 0
  • Are we doing this so that we can make sure we don't have any other effects, yet the bias will still be there?
  1. Add in the bias currents
  2. Add in the new resistor to balance out the bias currents
  3. Set the two (input terminal) nodal equations equal to each other and solve for the new resistor

Problem 2.17

Problem 2.17 after finishing step 4
  • Derive an expression for R in terms of the other resistor values, so that the output voltage due to the bias currents is zero.
  • Solving the two nodal equations for the terminal voltage and then setting the two equations equal to each other gives:
  • Solving for R gives:












Amplifier Circuits

Buffer Amplifier

Buffer Amplifier
  • Used to transfer voltage but not current to the following circuit. This amplifier can be used to negate the loading effects. No current flows through the amplifier, thus there is no voltage drop through the input resistor (going to the buffer amplifier).








Inverting Amplifier

Inverting Amplifier
  • Uses negative feedback to invert and amplify voltage. Using nodal analysis at the negative terminal, the gain is found to be









Summing Amplifier

Summing Amplifier
  • If all resistances are equal, then the output voltage is the (negative) sum of the input voltages













Noninverting Amplifier

Noninverting Amplifier








Differential Amplifier

Differential Amplifier
  • If you let and then the equation simplifies to