Chapter 3: Difference between revisions

From Class Wiki
Jump to navigation Jump to search
Line 24: Line 24:


===Clamp Circuit===
===Clamp Circuit===
*The direction of the diode will determine whether the positive or negative peaks are clamped.
*The charged capacitor value will determine the value the peaks are clamped at.
*Diodes are then used to define the upper and lower limit by conducting if the voltage goes outside their specified range.
*Diodes are then used to define the upper and lower limit by conducting if the voltage goes outside their specified range.
:*The direction of the diode will determine whether the positive or negative peaks are clamped.
:*The charged capacitor value will determine the value the peaks are clamped at.


===Linear Small-Signal Equivalent Circuits===
===Linear Small-Signal Equivalent Circuits===

Revision as of 13:08, 2 March 2010

Diodes

Diode.jpg
Diode load line
  • Forward bias occurs when the P-type semiconductor material is connected to the positive terminal of a battery and the N-type semiconductor material is connected to the negative terminal, as shown below. This usually makes the p–n junction conduct. <ref> Wikipedia P-N junction</ref>
  • Because diodes are a nonlinear device, traditional circuit analysis will not work on them. One method of analyze the diodes is to do it graphically. This technique is called Load-line analysis.
  • The load-line equation is obtained by applying KVL or KCL. The equation plots as a straight line that can be drawn by locating two points.
  • In circuits with multiple diodes, it is not immediately apparent which diodes are on or off. The ideal-diode model assumes that the diode is a perfect conductor with zero voltage drop in the forward direction and an open circuit in the reverse direction.
  1. Assume a set of states for the diodes
  2. Solve the circuit to find for diodes assumed to be on and for diodes assumed to be off
  3. Check to see if is positive for all diodes assumed to be on and if is negative for all diodes assumed to be off.
  • Explain peak inverse voltage, PIV.

Full Wave Recififier: Center-tapped Transformer

537px-SE Full wave rectifier - Center tapped.svg.png

Full Wave Recitifier: Diode Bridge

557px-Diode bridge alt 1.svg.png
557px-Diode bridge alt 2.svg.png
  • The diode bridge has a larger voltage drop due to two diodes in comparison to the center-tapped transformer.

Clipper Circuit

  • A battery + diode can be used to clip the circuit. A Zener diode will often take the place of the battery in a clipper circuit.
  • Placing a resistor in series with the diodes can allow for more gradual transfer characteristics.

Clamp Circuit

  • The direction of the diode will determine whether the positive or negative peaks are clamped.
  • The charged capacitor value will determine the value the peaks are clamped at.
  • Diodes are then used to define the upper and lower limit by conducting if the voltage goes outside their specified range.

Linear Small-Signal Equivalent Circuits

  • Dc supply voltages are used to bias a nonlinear device at an operating point and a small ac signal is injected into the circuit. If we consider a small enough region of operation, we can find a linear small-signal equivalent circuit.<ref>Electronics p156</ref>
  • The DC supply voltage results in the circuit operating at the quiescent point. We can use this point to find the dynamic resistance of the diode.
  • The analysis of nonlinear electronic circuits is often accomplished in two steps: First, the dc operating point is determined, and a linear small-signal equivalent circuit is found for the nonlinear devices; second, the equivalent circuit is analyzed. <ref>Electronics p188</ref>
  • Shockley Diode equation:
  • is the saturation current:
  • is the thermal voltage:
  • Dynamic small-signal resistance of the diode at the Q-point:

To Do

  • Start up Chapter 3 problems
  • Extend the bag of tricks post. Have subsections for op amps and diodes now. Then BJTs later.

References

<references/>