Chapter 4: Difference between revisions

From Class Wiki
Jump to navigation Jump to search
Line 114: Line 114:
{| class="wikitable" border="1"
{| class="wikitable" border="1"
|+?BJT Characteristics?
|+?BJT Characteristics?
! Type? !! Input Resistance || Output Resistance || Gain || Frequency response
! Type? !! Input Resistance || Output Resistance || Gain || Frequency response
|-
|-
| Common-emitter||
| Common-emitter|| || ||
|-
|-
| Common-collector|| ||
| Common-collector|| || ||
|-
|-
| Common-base|| ||
| Common-base|| || ||
|}
|}



Revision as of 17:48, 5 March 2010

Bipolar Junction Transistor

Base, Emitter, Collector

How a BJT works

  • NPN: Not Pointing iN
  • PNP: Pointing iN Please
  • The arrow is for the emitter current.
  • For an NPN the current flows into the collector. For a PNP the current flows out of the collector.
  • Quiescent is a none referring to a state of being quiet, still, at rest, dormant, inactive. In an electronic amplifier or filter is said to be in a quiescent state when no signal is applied to its input
Large Signal vs Small Signal Analysis
DC sources AC sources Capacitor BJT
DC analysis No change 0V or 0A Open-Circuit Active, Saturation or Cutoff
AC analysis 0V or 0A No change Short-Circuit Small-signal model

Signal Notation

  • Total =
  • DC =
  • AC =

Large-Signal DC models

BJT Regions
Base-Emitter Collector-Base Region
FB FB Saturation
FB RB Active
RB RB Cutoff
RB FB Reverse Active
Region Constraints
Region NPN PNP
Saturation and and
Active and and
Cutoff and and
  • Active: The normal mode of operation. This mode has the largest common-emitter current gain.
  • Reverse Active: The collector and emitter roles are reversed. Most BJTs are not symmetrical, thus and take on different values.
  • Saturation: High current from the emitter to collector. Logical "on".
  • Cutoff: Very little current flow. Logical "off".

Large-Signal DC Analysis

  1. Assume an operating region for the BJT.
  2. Solve the circuit to find
  3. Check the values to see if they match the region constraints.
IMG 0288.jpg
IMG 0287.jpg

Bias-Circuit Design

  • The principle goal of bias-circuit design is to achieve nearly identical operating points for the BJTs, even though the BJT parameters may vary significantly from unit to unit. <ref>Electronics p245</ref>
  • Fixed-base bias circuit is a very simplistic method that does not deal well with a wide variety of values. The base current does not adjust for changes in . If you want a circuit that has a particular operating point on the collector load line, the base current must change with .
  • Using two voltage sources (one for the collector and one for the base) achieves an emitter current that is relatively independent of . Usually only one source is available or we may wish to inject a signal into the base. In an ideal world you could simply place the voltage sources in series. Since the voltage sources are grounded, they would be put in parallel. The wire connecting the voltage source will see the potential difference (and a lot of current). The wire will burn up and bad things will happen to the voltage sources.
  • Four-resistor bias circuit provides a constant base voltage independant of . This design is great for discrete circuits, but is impractical in integrated circuits because of the excessive chip area they consume.
  • How does this handle injecting an ac source? How is it not coupled?

Small-Signal Equivalent Circuits

BJT Small Signal equivalent (both PNP & NPN)
  • Tranconductance:

Common-Emitter Amplifier

Common-emitter amplifier small-signal equivalent
  • A four-resistor biasing network
  • Coupling capacitor to separate the AC input/output from the DC biasing
  • Bypass capacitor allows for a common-emitter for AC, yet provides a stable bias current for DC
  • Voltage gain:
  • If and then and the gain is nearly independent of the transistor parameters.
  • Input Impedance: How do they get v_in (E4.45)? Why is v_o dependent on R^'_L instead of just R_L?
  • Current Gain & Power Gain:
  • Output Impedance:
  • Make sure you can run through Example 4.9















BJT models?

?BJT Characteristics?
Type? Input Resistance Output Resistance Gain Frequency response
Common-emitter
Common-collector
Common-base

Questions

  • Why do we always seem to use a common emitter configuration? Common-base and common-collector have different properties.
  • For P3.17 make the glob of sauder assuming they're all on and check the currents running through each one. Make sure they go the right way, and add up?
  • Why is the input/output impedance so important?
  • P4.54c

References

<references/>