Electromechanical Energy Conversion: Difference between revisions

From Class Wiki
Jump to navigation Jump to search
Line 61: Line 61:
# [http://kjmagnetics.com/products.asp?cat=13 Magnet Supplier]
# [http://kjmagnetics.com/products.asp?cat=13 Magnet Supplier]
# [http://en.wikipedia.org/wiki/Biot%E2%80%93Savart_law Biot Savart Law]
# [http://en.wikipedia.org/wiki/Biot%E2%80%93Savart_law Biot Savart Law]
# [http://136.159.225.44/AlliedData2.pdf Copper wire data (turns per inch, etc.)]
# [http://136.159.225.44/AlliedData2.pdf Copper wire data (turns per inch, resistance per foot, etc.)]


==References Used by the Professor==
==References Used by the Professor==

Revision as of 13:40, 14 February 2010

Rules

Class Roster

Points

Class Notes

Questions

What do we do when we are finished with the draft and ready to publish?

  • If it's been approved by the reviewers, move it to the articles section

Does anybody know of a way to put a box around text or math equations? Would I just have to create a 1x1 table?

Announcements

If anyone wants to write the derivation of Ampere's Law you can put it on my (Wesley Brown) Ampere's Law page and be a co-author.

Article Suggestions or Homework

(Please link these to the article when you complete it.)

  1. Rewrite the notes for the wiki. (Really, this will help get ready for the exam. The professor who did them is the one who is writing the exam questions.)
  • Effects of the Non-Linear B-H Curve
  1. Draw and explain the effect of the non-linear B-H curve on current waveforms for a voltage excited inductor. (This is mostly done in the notes.)
  2. Explain how to measure the B-H curve experimentally.
  3. If the B-H curve was traced out more quickly in the experiment above, would the curve look different? If so why?
  4. Show how to calculate the core losses of a nonlinear inductor using its i-v curve.
  • Transformers
  1. Explore transformers with more than one secondary winding.
    • What is the input impedance of an idea transformer with two secondaries, one with N2 turns and one with N3 turns, each with a different load resistor on attached.
    • How do the mutual impedances relate to the turns ratios in transformers with more than one secondary?
    • Develop a circuit model for a non-ideal transformer with multiple secondaries. (Follow the way we did it in class. You will have more mutual inductances. You may or may not be able to do it by using ideal transformers, but you should be able to do it with mutual impedances for sure.)
  2. Develop the theory of auto-transformers.
    • Come up with an ideal transformer model for auto-transformers.
    • Which part of the windings carries more current?
    • Is there any isolation with auto-transformers?
    • What if you have more than one tap on the auto-transformer? Can you come up with a model for that?
    • Develop a circuit model for a single tap auto-transformer.
  3. Explore how leakage flux affects the inductance of an inductor. What if that flux is then recovered and the effect accounted for by mutual inductance? Does the result agree with the simple calculation of inductance without leakage?
  4. Describe the coupling factor, k, used in Spice simulators and other circuit simulators. Relate it to the leakage, magnetizing, and mutual inductances.
  5. Derive the transformations.
  6. Explore the voltage regulation x 100% as a function of the power factor angle on the load of a transformer. (You will note some surprising results in some cases.)
  7. Describe the open circuit and short circuit test as applied to transformers.
  8. Explore how much flux is in the core of a loaded ideal transformer.
  • Three Phase Circuits
  1. Calculate and compare how much power can be delivered with three phase circuits as compared to a single phase circuits. Assume that the same amount of copper is available for the transmission lines of both systems.
  2. Compare and contrast the types of three phase transformers. (See the class handout.) Explain why each is better or worse in each situation.
    • Explain what the big deal is with third harmonic currents in three phase transformers. Where do they come from? Why does the delta winding minimize their effect on voltage distortion?

And if you don't understand any of the above, please see the teacher! He is willing to sit down with you and work any and/or all of the above.

Shaker Generator Project

Links to useful things on the web

  1. Shakemote
  2. An electromagnetic, vibration-powered generator for intelligent sensor systems
  3. MAX1724 DC to DC converter
  4. Magnetic Field on the axis of a cylinder
  5. Magnetic Field from a cylindrical magnet or solenoid
  6. Magnetic field as a function of length on a solenoid
  7. Magnet Supplier
  8. Biot Savart Law
  9. Copper wire data (turns per inch, resistance per foot, etc.)

References Used by the Professor

  1. Our text, by Mohan.
  2. Notes from Rod Heisler's Class
  3. Magnetic Circuits
  4. Transformer Model
  5. Transformer notes and some problems
  6. Notes from a Transformer Lecture in Sydney
  7. Three Phase Power
  8. Generator Animations
  9. The class handout on three phase transformer types from Glenn Masden. (I still have a couple of these that didn't get picked up in class.)
  10. Harmonics in Transformers
  11. Synchronous Machines
  12. Notes on Induction Motors

Draft Articles

These articles are not ready for reading and error checking. They are listed so people will not simultaneously write about similar topics.

Reviewed Articles

These articles have been reviewed and submitted.