Bootloader Programming: Difference between revisions
| (3 intermediate revisions by the same user not shown) | |||
| Line 4: | Line 4: | ||
We really should have provided a programming header for that as well as the one for the USB/serial programmer, but since we didn't, the professor will program your ATMEGA328P units using the information on [http://angryelectron.com/how-to-update-the-bootloader-on-arduino-pro-mini-328/ this web page]. |
We really should have provided a programming header for that as well as the one for the USB/serial programmer, but since we didn't, the professor will program your ATMEGA328P units using the information on [http://angryelectron.com/how-to-update-the-bootloader-on-arduino-pro-mini-328/ this web page]. |
||
On the USBtinyISP six pin header, the connections I made are: |
|||
Pin 1 in brown. |
|||
Pin 2 in red. |
|||
Pin 3 is orange. |
|||
Pin 4 is yellow. |
|||
Pin 5 is green. |
|||
Pin 5 is blue. |
|||
The connections on the Pro Mini are from [http://angryelectron.com/how-to-update-the-bootloader-on-arduino-pro-mini-328/ here]. [[File:Programmer connections.jpg]] |
|||
First I need to check to see that the fuses are okay, and that the USBtinyISP will work. |
First I need to check to see that the fuses are okay, and that the USBtinyISP will work. |
||
| Line 116: | Line 123: | ||
avrdude done. Thank you. |
avrdude done. Thank you. |
||
</nowiki> |
</nowiki> |
||
The next step was to unsolder the ATMEGA328P and solder in a new one to program. Sockets for these are expensive, and even if we had the budget, there is no time for any other method. |
|||
Latest revision as of 15:48, 4 March 2014
Bootloader Programming
The bootloader is a program that needs to be loaded into the ATMEGA328P before you can program your Arduino with the USB/serial programmer.
We really should have provided a programming header for that as well as the one for the USB/serial programmer, but since we didn't, the professor will program your ATMEGA328P units using the information on this web page.
On the USBtinyISP six pin header, the connections I made are:
Pin 1 in brown.
Pin 2 in red.
Pin 3 is orange.
Pin 4 is yellow.
Pin 5 is green.
Pin 5 is blue.
The connections on the Pro Mini are from here. 
First I need to check to see that the fuses are okay, and that the USBtinyISP will work.
$ avrdude -c usbtiny -p m328p avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.01s avrdude: Device signature = 0x1e950f avrdude: safemode: Fuses OK avrdude done. Thank you.
I read the original firmware into an Intel hex file using this command below just in case the ATmegaBOOT_168_atmega328_pro_8MHz.hex file doesn't work.
$ avrdude -c usbtiny -p m328p -U flash:r:original.hex:i avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.01s avrdude: Device signature = 0x1e950f avrdude: reading flash memory: Reading | ################################################## | 100% 50.06s avrdude: writing output file "original.hex" avrdude: safemode: Fuses OK avrdude done. Thank you.
Now I programmed the ATMEGA328 using the following command: Don't do this! It turned out to be a good thing I backed up the original firmware, because though the following programmed okay, I couldn't use the serial programmer to load sketches from the Arduino IDE.
$ avrdude -c usbtiny -p m328p -U flash:w:ATmegaBOOT_168_atmega328_pro_8MHz.hex
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.01s
avrdude: Device signature = 0x1e950f
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "ATmegaBOOT_168_atmega328_pro_8MHz.hex"
avrdude: input file ATmegaBOOT_168_atmega328_pro_8MHz.hex auto detected as Intel Hex
avrdude: writing flash (32652 bytes):
Writing | ################################################## | 100% 68.70s
avrdude: 32652 bytes of flash written
avrdude: verifying flash memory against ATmegaBOOT_168_atmega328_pro_8MHz.hex:
avrdude: load data flash data from input file ATmegaBOOT_168_atmega328_pro_8MHz.hex:
avrdude: input file ATmegaBOOT_168_atmega328_pro_8MHz.hex auto detected as Intel Hex
avrdude: input file ATmegaBOOT_168_atmega328_pro_8MHz.hex contains 32652 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 48.37s
avrdude: verifying ...
avrdude: 32652 bytes of flash verified
avrdude: safemode: Fuses OK
avrdude done. Thank you.
So after testing and finding this bootloader wouldn't allow programming sketches from the Arduino IDE, I flashed back the original firmware, and it worked.
$ avrdude -c usbtiny -p m328p -U flash:w:original.hex:i
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.01s
avrdude: Device signature = 0x1e950f
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "original.hex"
avrdude: writing flash (32670 bytes):
Writing | ################################################## | 100% 67.85s
avrdude: 32670 bytes of flash written
avrdude: verifying flash memory against original.hex:
avrdude: load data flash data from input file original.hex:
avrdude: input file original.hex contains 32670 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 49.58s
avrdude: verifying ...
avrdude: 32670 bytes of flash verified
avrdude: safemode: Fuses OK
avrdude done. Thank you.
The next step was to unsolder the ATMEGA328P and solder in a new one to program. Sockets for these are expensive, and even if we had the budget, there is no time for any other method.