Assembly Language Programming

From Class Wiki
Jump to navigation Jump to search


ARM7 Links

Raspberry Pi

Depending on the version, your pi may use ARM6 or ARM7. There is actually quite a lot of good assembly language information for programming the raspberry pi.

TI MSP430 Links

Toolchain

There are various toolchains (build tools) for the MSP430. TI provides the Code Composer Studio (both desktop, and browser based) toolchain. At this point, the desktop version is much more powerful than the browser based version, and you need it for this class. There are also some other toolchains that cost something, but I prefer Code Composer Studio.

Code Composer Studio

  • CCS will work with Linux and Windows, and now a beta is available for OS X.
    • To install CCSV6.1 on Ubuntu 15.04, you need to
$ unset JAVA_TOOL_OPTIONS

before running the installer. There is some more information for Linux installs here. I also found out that installing Grace from the App Center makes the App Center blank thereafter, unless you reinstall CCSV6.1.

MSP430 Assembly using the TI Assembler
MSP430 TI C Compiler
  • MSP430 Optimizing C/C++ Compiler (See Section 6.5 and following for how to mix C/C++ and Assembly. It is really best to read the entire chapter though, as it is all pertinent to mixing C and Assembly. It will also help you if you want to program in C, as it tells how the C compiler uses the memory, the stack, the registers, etc., and once you understand the processor as you learn to do when you learn its assembly language, it is very interesting to see how that all works in C.)
    • Here is how to use printf() statements with Code Composer Studio.
IAR Tools

IAR also makes a toolchain. It is not free, but you will sometimes find code that was developed for it, and it is slightly different from that developed for Code Composer Studio using either the TI or GCC compilers/assemblers.

GCC Compiler

You may use the GCC compiler from within Code Composer Studio. It is not limited in the size of the code that it can compile. There are some differences between it and the TI compiler. I find that the TI compiler usually works more easily, with TI examples especially.

To make your program using interrupt service routines compile with either the TI or the GCC compiler, you need some #ifdef's like this: 

#if defined(__TI_COMPILER_VERSION__) || defined(__IAR_SYSTEMS_ICC__)
#pragma vector=USCI_A0_VECTOR
__interrupt void USCI_A0_ISR(void)
#elif defined(__GNUC__)
void __attribute__ ((interrupt(USCI_A0_VECTOR))) USCI_A0_ISR (void)
#else
#error Compiler not supported!
#endif

Note that you need to substitute the appropriate ISR vectors in your code.

C Language References

Put a section here with |= and &= ~something, etc, that will help students understand how to translate from C to assembly.

MSP430F5529 Specific Data

Evaluation Board Data

Code Examples from Class

Other Course Materials for the MSP430 Family

CC3100 SimpleLink Wi-Fi Family

=2014 Robot Information

  • HSR-1425CR Continuous Rotation Servo Datasheet
  • Schematics These are rather crude schematics of the robot circuit board. There are two cuts and jumps that are not reflected, at least on the last one. The effect is to change the photo transistors from a common emitter to a common collector configuration. You can see the change scratched in just below the word Fairchild on the hand drawn schematic. Basically the resistor and photo transistor are reversed in order. I believe both photo transistors are swapped to common collector configuration.

2015 Robot Information

  • Building Tips
  • L9110 H Bridge Data Sheet
    • HG7881 Dual H Bridge Module This suggests putting the PWM signal on one input and the direction control on the other. If you do that, you need to invert the PWM input when you change directions as well. See the data sheet above.
  • Bluetooth UART HC-05 and HC-06
  • Blueberry Android Bluetooth Remote Control App
  • HY301-07A Photo Interrupter Datasheet From the datasheet, we will choose a forward current on the LED to be 5 mA because we don't want to waste batteries, and that is the lowest the data sheet shows it working. That leads us to a forward voltage across the diode of 1.3 volts. If we run things on 3.3 volts that gives us a voltage drop of 3.3-1.3=2.0 volts. Ohms law says a resistor of R=V/I=2volts/5mA = 400 ohms. We will pick 390 ohms since it is an available 5% value. For the phototransistor, we see that the current for the forward diode current we picked should be about 0.2 mA. If we want the output to drop to 0.5 volts with the LED on, that leaves 3.3 volts - 0.5 volts = 2.8 volts across the collector resistor, so using Ohm's Law again, we need a collector resistor of 2.8 volts/0.2mA = 14 Kohms, so we will pick 15 Kohms because it is a standard value. The 15 Kohm resistors are optional as you can use the built in ones on the MSP430 controlled by PREN.
  • I count 20 holes, on the encoder wheels. This gives 20 periods per revolution. The wheel diameter is about 0.066 meters, so the radius is 0.033 meters. This gives about 0.21 meters per revolution. It seems a pretty fast speed is about 1 meter per second, which means that we have about 5 revolutions per second, or 100 cycles per second, or about 0.01 seconds per period at high speed.
  • Applying Feedback makes the robot easier to control. This web page gives a somewhat helpful primer on that process.

Logic Analyzer Information

These logic analyzers are clones of the original Saleae analyzer. They have software compatible with this analyzer, but they don't like you to use it.

450

Other Miscellaneous Interesting Reading

Retrieved from "http:///class-wiki/index.php?title=Assembly_Language_Programming&oldid=11497"